北京恒正同创科技有限公司，博科Brocade光纤交换机金牌代理商，我们希望不仅为广大用户
提供优质的产品，更能在产品售后服务上令您满意，免除您的后顾之忧。产品动态详情请登录公司官网：www.brocader.com.cn
Brocade和Cisco光纤交换机级联配置
1.配置异构交换机平台协同工作模式
Cisco 9120配置过程
激活前8个端口
switch# config t
Enter configuration commands, one per line. End with CNTL/Z.
switch(config)#interface fc1/1-8
switch(config-if)# no shutdown switch(config-if)# end
配置交换机协同工作模式
switch# config t
Enter configuration commands, one per line. End with CNTL/Z.
switch(config)# vsan database
switch(config-vsan-db)# vsan 1 interop
switch(config-vsan-db)# end
配置domain ID
switch# config t
Enter configuration commands, one per line. End with CNTL/Z.
switch(config)# fcdomain domain 100 preferred vsan 1
switch(config)# end
激活VSAN
switch# config t
Enter configuration commands, one per line. End with CNTL/Z.
switch(config)# vsan database
switch(config-vsan-db)# vsan 1 suspend
switch(config-vsan-db)# no vsan 1 suspend
switch(config-vsan-db)# end
察看修改之后的系统配置信息
switch# show running
version 2.0(2b)
vsan database
vsan 1 interop 1
fcdomain domain 100 preferred vsan 1
fcdomain fcid persistent vsan 1
boot kickstart bootflash:/m9100-s1ek9-kickstart-mz.
boot system bootflash:/m9100-s1ek9-mz.2.0.2b.bin
kernel core target 0.0.0.0
kernel core limit 1
snmp-server user admin network-admin auth md5 0xeec64ba2afbe9b65e13b
priv 0xeec64ba2afbe9b65e13b
username admin password 5 $1$V3smTQpb$MTvub69DkVBxdCt9BsEDB1 role network-admin
callhome
switch-priority 7
snmp-server enable traps license
interface mgmt0
ip address 192.168.70.139 255.255.255.0
interface fc1/1
no shutdown
interface fc1/2
no shutdown
interface fc1/3
no shutdown
interface fc1/4
no shutdown
interface fc1/5
no shutdown
interface fc1/6
no shutdown
interface fc1/7
no shutdown
interface fc1/8
no shutdown
interface fc1/9
interface fc1/10
interface fc1/11
interface fc1/12
interface fc1/13
interface fc1/14
interface fc1/15
interface fc1/16
interface fc1/17
interface fc1/18
interface fc1/19
interface fc1/20
switch#
察看端口连接状态信息
switch# show interface brief
-------------------------------------------------------------------------------
Interface Vsan Admin Admin Status FCOT Oper Oper Port
Mode Trunk Mode Speed Channel
Mode (Gbps)
-------------------------------------------------------------------------------
fc1/1 1 auto on up swl F 2 --
fc1/2 1 auto on up swl F 2 --
fc1/3 1 auto on up swl E 2 --
fc1/4 1 auto on notConnected swl -- --
fc1/5 1 FX -- notConnected swl -- --
fc1/6 1 FX -- notConnected swl -- --
fc1/7 1 FX -- notConnected swl -- --
fc1/8 1 FX -- notConnected swl -- --
fc1/9 1 FX -- sfpAbsent -- -- --
fc1/10 1 FX -- sfpAbsent -- -- --
fc1/11 1 FX -- sfpAbsent -- -- --
fc1/12 1 FX -- sfpAbsent -- -- --
fc1/13 1 FX -- sfpAbsent -- -- --
fc1/14 1 FX -- sfpAbsent -- -- --
fc1/15 1 FX -- sfpAbsent -- -- --
fc1/16 1 FX -- sfpAbsent -- -- --
fc1/18 1 FX -- sfpAbsent -- -- --
fc1/19 1 FX -- sfpAbsent -- -- --
fc1/20 1 FX -- sfpAbsent -- -- --
刀片中心光纤交换机模块配置
禁止交换机
brocadessm:USERID> switchdisable
修改Domain ID
brocadessm:USERID> configure
Configure...
Fabric parameters (yes, y, no, n): [no] yes
Domain: (1..239) [1] 99
R_A_TOV: (4000..120000) [10000]
E_D_TOV: (1000..5000) [2000]
WAN_TOV: (0..30000) [0]
MAX_HOPS: (7..19) [7]
Data field size: (256..2112) [2112]
Sequence Level Switching: (0..1) [0]
Disable Device Probing: (0..1) [0]
Suppress Class F Traffic: (0..1) [0]
Switch PID Format: (1..2) [1]
Per-frame Route Priority: (0..1) [0]
Long Distance Fabric: (0..1) [0]
BB credit: (1..27) [16]
Insistent Domain ID Mode (yes, y, no, n): [no]
Virtual Channel parameters (yes, y, no, n): [no]
Zoning Operation parameters (yes, y, no, n): [no]
RSCN Transmission Mode (yes, y, no, n): [no]
Arbitrated Loop parameters (yes, y, no, n): [no]
System services (yes, y, no, n): [no]
Portlog events enable (yes, y, no, n): [no]
ssl attributes (yes, y, no, n): [no]
http attributes (yes, y, no, n): [no]
snmp attributes (yes, y, no, n): [no]
rpcd attributes (yes, y, no, n): [no]
cfgload attributes (yes, y, no, n): [no]
webtools attributes (yes, y, no, n): [no]
WARNING: The domain ID will be changed. The port level zoning may be affected
brocadessm:USERID> msPlMgmtDeactivate
Switch is in Offline state.
修改协同工作模式
brocadessm:USERID> interoper mode 1
The switch effective configuration will be lost when the operating mode is changed; do you want to continue? (yes, y, no, n): [no] y
Interopmode is enabled
Note: It is recommended that you reboot this switch for the new change to take effect.
重新引导交换机
brocadessm:USERID> fastboot
Broadcast message from root (pts/0) Tue Jun 13 10:07:45 2006... The system is going down for reboot NOW !! USERID
Password:
Please change your passwords now.
Use Control-C to exit or press 'Enter' key to proceed.
Password was not changed. Will prompt again at next login
until password is changed.
brocadessm:USERID>
激活交换机
brocadessm:USERID> switchenable
察看修改配置之后的交换机状态
brocadessm:USERID> switchshow
switchName: brocadessm
switchType: 22.0
switchState: Online
switchMode: Interop
switchRole: Principal
switchDomain: 99
switchId: fffc63
switchWwn: 10:00:00:05:1e:02:78:c6
zoning: OFF
switchBeacon: OFF
Area Port Media Speed State
==============================
0 0 id
1 1 cu
2 2 cu
3 3 cu
4 4 cu
5 5 cu
6 6 cu
7 7 cu
8 8 cu
9 9 cu
10 10 cu
11 11 cu
12 12 cu
13 13 cu
14 14 cu
15 15 id
2.划分zone
Cisco 9120划分zone
察看fabric连接设备port wwn 信息
switch# show fcns database vsan 1
VSAN 1:
--------------------------------------------------------------------------
FCID TYPE PWWN (VENDOR) FC4-TYPE:FEATURE
--------------------------------------------------------------------------
0x630100 N 21:00:00:14:5e:24:a9:04 scsi-fcp
0x630200 N 21:00:00:14:5e:24:a9:36 scsi-fcp
0x630300 N 21:00:00:14:5e:24:a9:
0x630400 N 21:00:00:14:5e:24:a9:b6 scsi-fcp
0x630500 N 21:00:00:14:5e:24:a9:28 scsi-fcp
0x630600 N 21:00:00:14:5e:24:aa:f6 scsi-fcp
0x630700 N 21:00:00:14:5e:24:aa:f0 scsi-fcp
0x630800 N 21:00:00:14:5e:24:a9:38 scsi-fcp
0x640000 N 20:07:00:a0:b8:21:19:
0x640100 N 20:06:00:a0:b8:21:19:
Total number of entries = 10
创建zone
分别创建2个zone，前4个刀片服务器与DS4300 2个控制器组成的zone，第4到第8个刀片服务器与DS4300 2个控制器组成的zone。
switch# config t Enter configuration commands, one per line. End with CNTL/Z.
switch(config)# zone name blade_hs20_1-4 vsan 1
switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:04
switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:36
switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:
switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:b6
switch(config-zone)# member pwwn 20:07:00:a0:b8:21:19:
switch(config-zone)# member pwwn 20:06:00:a0:b8:21:19:
switch(config-zone)#exit
switch(config)# zone name blade_hs20_5-8 vsan 1
switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:28
switch(config-zone)# member pwwn 21:00:00:14:5e:24:aa:f6
switch(config-zone)# member pwwn 21:00:00:14:5e:24:aa:f0
switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:38
switch(config-zone)# member pwwn 20:07:00:a0:b8:21:19:
switch(config-zone)# member pwwn 20:06:00:a0:b8:21:19:
创建zoneset
switch(config-zone)# zoneset name ds4300_blade vsan 1
switch(config-zoneset)# member Blade_Hs20_1-4
switch(config-zoneset)# member Blade_Hs20_5-8
switch(config-zoneset)# end
激活zoneset switch# config t Enter configuration commands, one per line. End with CNTL/Z.
switch(config)# zoneset activate name ds4300_blade vsan 1 Zoneset activation initiated. check zone status
察看激活的zone信息
switch# show zone active vsan 1
zone name blade_hs20_1-4 vsan 1
* fcid 0x630100 [pwwn 21:00:00:14:5e:24:a9:04]
* fcid 0x630200 [pwwn 21:00:00:14:5e:24:a9:36]
* fcid 0x630300 [pwwn 21:00:00:14:5e:24:a9:
* fcid 0x630400 [pwwn 21:00:00:14:5e:24:a9:b6]
* fcid 0x640000 [pwwn 20:07:00:a0:b8:21:19:
* fcid 0x640100 [pwwn 20:06:00:a0:b8:21:19:
zone name blade_hs20_5-8 vsan 1
* fcid 0x630500 [pwwn 21:00:00:14:5e:24:a9:28]
* fcid 0x630600 [pwwn 21:00:00:14:5e:24:aa:f6]
* fcid 0x630700 [pwwn 21:00:00:14:5e:24:aa:f0]
* fcid 0x630800 [pwwn 21:00:00:14:5e:24:a9:38]
* fcid 0x640000 [pwwn 20:07:00:a0:b8:21:19:
* fcid 0x640100 [pwwn 20:06:00:a0:b8:21:19:
保存系统配置信息
switch# copy running startup
[########################################] 100%
刀片中心光纤交换机模块查看zone信息
brocadessm:USERID> cfgshow
Defined configuration:
no configuration defined
Effective configuration:
cfg: ds4300_blade
zone: blade_hs20_1-4
21:00:00:14:5e:24:a9:04
21:00:00:14:5e:24:a9:36
21:00:00:14:5e:24:a9:
21:00:00:14:5e:24:a9:b6
20:07:00:a0:b8:21:19:
20:06:00:a0:b8:21:19:
zone: blade_hs20_5-8
21:00:00:14:5e:24:a9:28
21:00:00:14:5e:24:aa:f6
21:00:00:14:5e:24:aa:f0
21:00:00:14:5e:24:a9:38
20:07:00:a0:b8:21:19:
20:06:00:a0:b8:21:19:
如上命令输出所示，Cisco 9120的zone 信息已经同步到刀片中心的交换机模块。
系统配置完成。
