PLC模块6AG1323-1BH01-2AA0-工控行业信息网(chinagkong.com)-工控行业门户网站

产品简介

PLC模块6AG1323-1BH01-2AA0

产品价格：￥2000

上架日期：2017-02-22 10:07:49

产地：德国

发货地：上海

供应数量：不限

最少起订：1台

浏览量：57

点击询价 QQ洽谈

资料下载：暂无资料下载

其他下载：暂无相关下载

详细说明

数字量输入/输出模块适用于连接：

标准开关和两线制接近开关(BERO)
电磁阀、接触器、小功率电机、灯和电机启动器

Design

数字量输入/输出模块具有下列机械特性：

紧凑型设计：
- 绿色 LED，用于指示输入/输出的信号状态，
- 插入前连接器
- 前门上的标签区
- 连接器针脚分配，用于在前门内部进行配线。
安装简单：
没有插槽规则；输出地址由插槽决定。
当在 ET 200M 中与有源总线模块一起使用时，可以进行热插拔，而不会有任何反应。
方便用户接线

Functions

数字量输入/输出模块转换

来自过程的外部数字信号电平转换成控制器内部信号电平
将控制器的内部信号电平转换成过程所要求的外部信号电平。

SM 327 是一个可升级的I/O模块。共有16个通道，其中8个通道是固定的，另8个通道可分别用作输入或输出。因此，该组和模块可以灵活地满足任何组合的需要。

Technical Specifications

Order number		6AG1323-1BH01-2AA0
		SIPLUS SM323 8DE/8DA
Supply voltage
Load voltage L+
● Rated value (DC)		24 V
Input current
from load voltage L+ (without load), max.		40 mA
from backplane bus 5 V DC, max.		40 mA
Power loss
Power loss, typ.		3.5 W
Digital bs
Number of digital bs		8
Input characteristic curve in accordance with IEC 61131, type 1		Yes
Number of simultaneously controllable bs
horizontal installation
— up to 60 °C, max.		8
vertical installation
— up to 40 °C, max.		8
Input voltage
● Type of b voltage		DC
● Rated value (DC)		24 V
● for signal "0"		-30 to +5V
● for signal "1"		13 to 30V
Input current
● for signal "1", typ.		7 mA
Input delay (for rated value of b voltage)
for standard bs
— at "0" to "1", min.		1.2 ms
— at "0" to "1", max.		4.8 ms
Cable length
● shielded, max.		1 000 m
● unshielded, max.		600 m
Digital outputs
Number of digital outputs		8
Short-circuit protection		Yes
● Response threshold, typ.		1 A
Limitation of inductive shutdown voltage to		L+ (-53 V)
Controlling a digital b		Yes
Switching capacity of the outputs
● on lamp load, max.		5 W
Load resistance range
● lower limit		48 Ω
● upper limit		4 kΩ
Output voltage
● for signal "1", min.		L+ (-0.8 V)
Output current
● for signal "1" rated value		0.5 A
● for signal "1" permissible range, min.		5 mA
● for signal "1" permissible range, max.		0.6 A
● for signal "1" minimum load current		5 mA
● for signal "0" residual current, max.		0.5 mA
Output delay with resistive load
● "0" to "1", max.		100 μs
● "1" to "0", max.		500 μs
Parallel switching of two outputs
● for uprating		No
● for redundant control of a load		Yes; only outputs of the same group
Switching frequency
● with resistive load, max.		100 Hz
● with inductive load, max.		0.5 Hz
● on lamp load, max.		10 Hz
Total current of the outputs (per group)
horizontal installation
— up to 60 °C, max.		4 A
vertical installation
— up to 40 °C, max.		4 A
Cable length
● shielded, max.		1 000 m
● unshielded, max.		600 m
Encoder
Connectable encoders
● 2-wire sensor		Yes
— permissible quiescent current (2-wire sensor), max.		2 mA
Isochronous mode
Isochronous operation (application synchronized up to terminal)		No
Interrupts/diagnostics/status inbation
Alarms		No
Diagnostic functions		No
Diagnostics indication LED
● Status indicator digital output (green)		Yes
● Status indicator digital b (green)		Yes
Potential separation
Potential separation digital bs
● between the channels		Yes
● between the channels, in groups of		8
● between the channels and backplane bus		Yes; Optocoupler
Potential separation digital outputs
● between the channels		Yes
● between the channels, in groups of		8
● between the channels and backplane bus		Yes; Optocoupler
Isolation
Isolation tested with		500 V DC
Standards, approvals, certificates
CE mark		Yes
UL approval		Yes; File E239877
FM approval		Yes; CofC 3028431
RCM (berly C-TICK)		Yes
KC approval		Yes
EAC (berly Gost-R)		Yes

请相信上海西皇自动化科技有限公司是您忠诚的长久的合作伙伴，我们愿与广大客户携手向前，共同进步！