The following explanations supports this endeavours with regards to correct bs for unintentional and undesired debation of fabric conveyor belts.下面的解释方面无意的和不受欢迎的织物输送带变形的正确表达式支持这种努力 。
Note: Do not use the b “curved belt” to describe undesired belt debation, because this is typically used to refer to powerturn belts.注意： 不要使用“弧形地带”来形容不受欢迎的皮带变形，因为这是通常用来指powerturn安全带。
Cambered belt (“banana shape”)弧形带（“香蕉形状”） A cambered belt is characterized by a longitudinal curvature of the belt relative to its centerline due to different internal stresses:一个弧形带的特点是由一个带相对其中心线，由于不同的内部应力的纵向曲率：
Camber can be caused by可引起康贝 • the manufacturing process•在制造过程 • environmental conditioning of the material (namely with belts with polyamide trb layer due to hygroscopic behaviour)•环保空调的物质（即聚酰胺牵引层由于带的吸湿行为 ） • improper storage ie storing belt on its edge (different conditioning over the coil b, one belt edge gets longer than the other)•储存不当，即存储在其边缘带（在线圈宽度不同的空调，一个带的边缘变得长于其他 ）
Common colloquialism for belt camber is “banana effect” or “banana belt”.带拱常见的俗语是“香蕉效应”或“香蕉带”。
Joint (splice) misalignment联合（拼接）不对 Joint (splice) misalignment is commonly the result of improperly squared belt ends.联合（拼接）不对通常不当平方带两端的结果 。This effect is seen as a cyclic lateral drifting of the belt as the joint (splice) approaches and passes a reference point on the conveyor:这种效应被看作是一个循环的横向联合（拼接）方法带漂流，并通过一个传送带上的参考点：
Joint (splice) misalignment can also be caused by an improper slitting, if the end of the belt leaves the constraint of the guides that direct the belt into the slitter:联合（拼接）不对也可以造成不当的纵切，如果传送带末端离开导游直接带分切机的约束：
Edge cbing卷边Habasit(哈伯斯特) Edge cbing is characterized by a transversal concave or convex dished belt ed ges :卷边的特点是由横向的凹或凸抛出带版 GES：
Belt cupping (or dishing)腰带拔罐（或抛出）Habasit(哈伯斯特) Belt cupping, also called dishing, is characterized by an unintentional transversal concave or convex belt dishing over the whole belt b:腰带拔罐，也被称为凹陷，特点是由无意的横向凹或凸的皮带在整个皮带宽度抛出 ：
Belt waving皮带挥舞Habasit(哈伯斯特) Belt waving皮带挥舞is characterized by longitudinal waves, which propagate across the belt's b :纵波，它传播到皮带的宽度的特点是 ：
Belt buckling带屈曲 Belt buckling带屈曲is the bation of a longitudinal ridge in the belt typically along the centre of the belt b.是一个在腰带上，通常沿皮带宽度的中心的纵脊的形成。In extreme cases the buckled belt may overlap/fold over :在极端情况下扣皮带可能会重叠/倍以上：
Belt edge rippling带的边缘荡漾Habasit(哈伯斯特) Edge rippling is characterized by longitudinally corrugated edges:边缘纵向波纹边荡漾着的特点是：
