测量对象:		气体中的固体粒子(无粒子构成限制)
粒子大小:		0.3µm或更大
测量范围:		0.1mg/m3　~　1kg/ m3
测量原理:		摩擦静电检测方式
测量条件:		温度最高250℃ 压力最大200kPa 气体流速最小4m/s(最大30m/s) 湿度最大40vol% 输入浪涌电压最大100V(超过500V时，可能会造成转换器的损坏)
测量量程:		可通过自动调节按钮进行快速设定，也可以进行手动设定。手动设定仅适用于流向监视器(DT450G-3)
模拟输出信号:		4~20mA DC(隔离，负载电阻500Ω) (仅适用于流向监视器DT450G-3)
接点输出信号:		接点电容:5A、24V AC或3A、24V DC (用于上下限报警)
接点类型:		NO(输出报警时“关”)或NC、2点输出 ※继电器在输出报警时励磁
定时数:		10~300秒(10秒步进)
参考工作条件:		环境温度:-20~45℃ 环境湿度:低于95%RH(无结露) 振动低于5m/s2(0.5G)
结构:		探头与转换器一体式(传感探头:直接插入式)、防雨结构IP64
电源:		100~120V AC、50/60Hz或200~240V AC、50/60Hz
质量:		约2.3kg(不包括法兰盘)
外形尺寸:		172W X 173H X 672D mm

DT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-ADT450G-1-2-05-1-A-E-A-A