ZJW泵@保定耐腐蚀杂质泵@耐腐蚀杂质泵规格齐全

2，厢式压滤机活动压板压紧力不足活动压板压紧力是由电接点压力表控制，活动压板压紧力不足电接点压力表压力调节不当，高压液流阀调节不当，各阀油路泄漏严重，油液脏堵塞阀体。解决的方法是电接点压力表，高压液流阀重调，高，低压溢流阀先扭开前端端盖，点动电机启动油泵冲洗，检查各阀油路泄漏情况，更换密封接口垫。油液太脏或使用时间超过一年，更换。 3.2保压失灵。

一、产品概述

ZJW型压滤机专用泵本由公司结合各压滤机生产厂家及使用现场的实际工况，精心设计开发的新一代无泄漏压滤机专用泵，该产品广泛应用于压滤机入料泵应用尤为广泛，通过在冶金、矿山、电厂、化工等行业中的使用，发现该系列产品具有结构

合理，运行可靠，寿命长等特点。该系列产品采用独特的水力设计及双级叶轮的结构，确保了其性能曲线比一般YLB、UHB、HFTK等普通离心泵改造而成的压滤机入料泵更陡，更适合压滤机入料的特殊使用工况。jdhuiquan4.12

ZJW泵@保定耐腐蚀杂质泵@耐腐蚀杂质泵规格齐全

2, on the drawing board the trolley, chain sprockets, bearings, and other parts of the piston rod must have a timing check, the respective holding members cooperate clean, smooth and well-functioning hydraulic press using the specification to ensure that sensitive, for pulling catenary chain synchronization and timely adjustments to board the trolley. 3, for the conservation of the hydraulic system, mainly to view and maintain the tightness of the hydraulic components and various interfaces. Plate and frame filter press is not used for a long time, the filter plate and frame filter should be cleaned on a regular emission filter rack after cleansing. After the dry cleaning cloth, revealing some of the piston rod and the manifold should be coated with butter.

二、创新技术特点
1.独特的密封装置采用负压技术加组合密封装置，在压力不断增加而流量逐渐减少的情况下，密封组件不承受压力，尤其是在后期压榨期时因泵在大压力下，其创新密封结构设计，保证轴封处基本达到无泄漏。

2.双级叶轮的结构设计
  该泵采用双主泵体，双主叶轮的结构设计，解决了单泵单叶轮泵在入料初期时振动和噪音过大、性能曲线平坦、叶轮流道窄、通过性能差等缺点非常适合压滤机入料时应阻力的变化来实现大流量低压力喂料与小流量、高压力过滤的要求。

3.双叶轮泵比单叶轮泵抗耐磨性更好
  因双叶轮泵以较低的叶轮出口线速度获得更高的泵出口压力从而克服了单叶轮泵为增加压力而增加叶轮线速度，而导致叶轮、泵壳磨损加剧的缺点，有效的提高水泵等过流部件的寿命。

4.应用范围广
  该产品可采用铸钢、高铬铸铁（耐腐耐磨材料）、不锈钢等多种材质制造，可适合不同的介质需求，用户选用的范围更广。

5.叶轮与泵壁的间隙可调
  独特的轴承箱设计，用户在常时间使用后，因磨损造成压力下降时，可通过调整叶轮与泵壁的间隙来继续保障水泵的高压力，提高了水泵的使用寿命、延长了大修周期，克服了传统单叶轮压滤泵因磨损压力下降快，经常更换叶轮使用寿命短等缺点。

ZJW泵@保定耐腐蚀杂质泵@耐腐蚀杂质泵规格齐全

Lotion slowly open the intake valve or the air intake, the cake is washed or dried. After the operation is completed, wash off the pump or compressor and the valve, cake discharge operation can be carried out. The fourth step cake discharge: first turn off the feed pump and the feed valve, lotion, or into the air intake means and the valve, then press and hold the "release" button on the operation panel, the pressing plate to drive the piston rod retracted, suitable retreat rear b, the release hold the "release" button to remove the filter plate is pulled by block artificial cake, while cleaning the sealing surface of the adhesive residue to prevent the sealing surface of the filter cake sandwiched affect the sealing perbance. Generating leakage after full press cake: a third washing step or dried. Shutting down the feed pump and the feed valve. Wash pump or compressor opened to this one operation cycle is completed.

三、性能参数表

ZJW泵@保定耐腐蚀杂质泵@耐腐蚀杂质泵规格齐全

Correction step: 1, finishing groove, a fresh surface to leakage, can be used, such as finishing blade 2 small, two kinds of non-healing agent 1: 3 good distribution, good quick sets share a filter cloth, the filter plates squeezed together, so that Putty cloth and glued together, squeezed together with flat grooves 4, the repair agent coated on the allocated grooves, painted higher.

电力，煤炭，石油化工，环境保护工程，建材，火电烟气脱硫，污水处理，城市工厂给排水等许多范畴。 公司的泵型首要有：ZJ(L) AH HH AHR SPR型渣浆泵，D，DT，TL。矿山河北会泉泵业有限公司产品广泛应用于冶金TLL系列脱硫泵HW混流泵实力和产质量量取得业界的认可。