水利工程泵@井陉矿水利工程泵@水利工程泵150口径

Suction tank should be easy to clean before. (4) Considering the landing of the water surface, the b of the suction pipe end should have enough submerged depth to prevent the intake from the whirlpool. (5) Before installation, to carefully check whether the bottom valve is flexible, at the same time in order to facilitate inspection and maintenance, to consider a good installation b. (6) The gate valve installed on the inlet side shall be installed in a horizontal direction or tilted downwards to avoid the accumulation of air. Import Side Gate valve In addition to inspection, switching outside, must be fully open. At the same time should try not to let the air from the sealing sleeve area. (7) The bending part is as smooth as possible, reducing the number of elbows, and should try to avoid being set close to the inlet of the pump. (8) When there is a different diameter tube, in order not to allow air to accumulate, should use eccentric type of pipe. (9) For parallel operation of the pump inlet pipe, it is advisable to use a separate water inlet pipe. If the use of direct to the common mother tube, easy to occur the imbalance of import pressure. The drive (motor) drives the impeller to rotate through the pump shaft, and the blade of the impeller drives the liquid to rotate together.

运行数据：出口直径：DN=80～800mm流量：50～11600m3/h(额定点)扬程：H＝7.6～200m(额定点)许用工作压力：≤2.5MPa许用试验压力：≤3.75MPa介质：清水或物理化学性质类似于清水的其它液体(固体颗粒≤80mg/L)。温度：≤105°C水力经优化设计三水力模型，不仅使泵具有优异的水力性能，并且没有轴向力(理论上)这一困扰水泵特别是大型水泵运行的难题。泵体、泵盖、叶轮经精密铸造，过流表面光滑提高了泵的抗汽蚀性能和效率。密封根据输送介质或用户要求采用填料密封或机械密封，不受转向限制。对于填料密封，有足够的空间用于更换填料。jdhuiquan4.13

水利工程泵@井陉矿水利工程泵@水利工程泵150口径

不可忽略对中开泵可靠性方面的要求，总之通过我们的努力要获得一款效率高汽蚀性能好，运行可靠稳定的好泵。中开泵主要适用于输送不含固体颗粒的介质。因此这种泵可以在石油，化工以及电力等行业进行应用，比如说在石化中延迟焦化，火电厂中的中型锅炉给水等。这种类型的泵在维护方面非常的方便，因此在相关的行业中得到了广泛的应用。由于泵内的各种损失泵的有效功率总是小于轴功率，故效率总是小于1的。目前国内中开泵中多数型号的效率一般在70-80％左右，少数大流量型号的效率在90%左右。影响中开泵效率的主要原因在于泵内存在的能量损失，这些损失主要是机械损失，水力损失和容积损失。机械损失主要是叶轮外表面与液体的磨擦损失（即圆盘摩擦损失）以及离心泵轴承。

产品概述：S、SA系列双吸中开泵，主要供输送温度不高于105°C的清水或理化性质类似于水的液体。适用于自来水厂、泵站、电站、空调循环用水、采暖用热水循环、工业供水系统、消防系统、船舶、炼油工业(一般性液体)等输送液体的场合。

产品特点：

1、内置式密封润滑结构：泵内置式密封润滑结构，密封循环水对泵密封系统的润滑、冲洗更为直接、有效。  

2、外形美观：直线型的外观并在泵盖上附加强筋，内置式密封润滑结构使泵整体结构浑然一体，灵活的结构设计使泵更加精美大方。  

3、率：采用CFD计算流体动力学，分析计算出泵内压力分布和速度分布关系、优化泵的流道设计，确保泵有的水力形线，提高了泵的效率。泵体采用双流道设计，以减小径向力。泵体、泵盖、叶轮等过流部采用树脂砂板模造型，保证了外观及流道尺寸以及泵的水力效率。S、SA系列双吸中开泵效率比一般双吸泵高3～5％。  

4、平衡精度高：转子部件动平衡精度为G1。0级。  

5、轴：轴短且刚性好，增加轴径，以延长轴承和机械密封的使用寿命。轴为全封结构，确保了不与介质接触，不锈蚀，使用寿命长。  

6、双蜗壳：高扬程泵采用双蜗壳结构，减轻了径向力。

水利工程泵@井陉矿水利工程泵@水利工程泵150口径

In order to achieve the purpose of sealing, while the dynamic ring and static ring has a lubrication effect. The medium-open pump is regularly inspected during operation. The characteristics of the use of mechanical seals in medium-open pumps 1, the main advantage of the mechanical seal of the medium open pump is that the seal is reliable in a long life cycle, the leakage is very few, the effect is long, generally can use about 5 years, the maintenance cycle is long. However, the mechanical seal structure is complex, the manufacturing and installation precision is high, the lattice is high, the technical request to the maintenance personnel is high. Therefore, it is very important to ensure the reliable operation of mechanical seals and extend the service life of mechanical seals. Of course, the price sealed with seasoning is cheap, the technical requirements are relatively low. The problem that the mechanical seal of medium open pump is easy to occur in the process of use, the main problem that the mechanical seal is easy to occur is the leakage amount is very poor and the temperature is too high. Touch the mechanical seal cover with your hand, and if you can't stay on it, it means the temperature is too high. Leakage per side should not exceed 60 drops of/min, if linear flow, it indicates that the amount of leakage is too large, can determine whether to observe the operation;

工作条件：

1．许用工作压力为2.5MPa；即泵入口压力+泵扬程≤2.5MPa。根据泵壳承受的压力，泵体和泵盖材质采用灰口铸铁(1.6MPa)、球墨铸铁(2.0MPa)、铸钢(2.5MPa)。在订货时敬请注明泵的承压情况或材质。

2．介质：温度≤105°C的清水或物理化学性质类似清水的其它液体(固体颗粒≤80mg/L)。 轴承1、采用油脂润滑的封闭式滚动轴承，维护简单，运行时间长；2、配备恒定油位的油杯，也可用稀油润滑；

3、选用进口(SKF、NSK、NTN)高质量轴承，运行平稳，噪音低，使用寿命长。 结构 结构紧凑、稳定性好。

S、SA系列双吸中开泵为泵壳中开结构，进出口均在泵体上，检修时只需吊出泵盖，转子部件便可移出进行检修作业，而不需拆卸管路，十分方便。 根据需要电动机(驱动机)可以在左端也可在右端，方便现场安装。结构上缩短转子部件轴向尺寸，轴的钢性更好，运行更稳定可靠。设有泵体密封环，而叶轮密封环为可选用件。密封环磨损后可以更换，减少了运行维护费用。

五、型号意义：

例如：300S58A

　　　300-泵入口直径(mm)

　　　S-单级双吸水平中开式离心清水泵

　　　58-设计点扬程(m)

　　　A-叶轮外径改变标志

功率选择兴衰，本质选择胜败”的政策教训下，不断开荒跋涉，立异打开。出售网点辐射全国各大城市，产品行销全国各省，市，自治区，并出口东南亚等国。企业以一流的处理。质量选择命运企业在“产品选择出路一流的产品，一流的效能赢得了广大用户的信赖和好评。

中小型企业会越来越多，产品迭代速度也会越来越快。关键工序核心装备数控化率超过85%；区域两化融合发展水平综合指数达115，产业主要环节信息化应用达到国内同行业先进水平，推动公共平台建设，整合生产以及研发设计、集成、监测认证、专业外包、市场开拓等资源，连接产学研政各方力量，近年来，整个建材家居行业都面临着原材料上涨、市场竞争加强以及消费需求变化的多重考验。近年来，随着五金行业发展迅速，市场品牌众多、竞争激烈，此时品牌建设成为了五金企业发展争夺的又一阵地。