外贴式橡胶止水带EB型

中埋式橡胶止水带必须采取可靠的固定措施，避免在浇注混凝土时发生位移，保证止水带在混凝土中的正确位置。对于固定橡胶止水带时，只能在止水带的允许部位上穿孔打洞，不得损坏本体部分。对于止水带的固定方法应按设计要求的施工规范进行，常用的固定方法有：利用附加钢筋固定；专用卡具固定；用铅丝和模板固定
The bded rubber water stop must take reliable measures to avoid displacement when pouring concrete, and ensure the correct b of the water stop belt in the concrete. When the rubber sealing belt is fixed, the perforated hole can only be perforated on the allowed part of the water stop belt, and the part of the body can not be damaged. For the fixed b of waterstop shall be in accordance with the design requirements of the construction specifications, fixation bs are commonly used: the use of additional reinforcement fixation; special fixture fixation; fixation with wire and template
等。不论采用何种固定方法，都必须保证止水带定位准确，不损坏止水带有效部分，方便混凝土浇捣。
Etc.. No matter what fixed b used, it is necessary to ensure the accurate bing of the water stop belt, not damage the effective part of the water check belt, convenient concrete pouring.
应尽量在工厂中连接成整体。如因制造工艺、运输条件等限制，需在现场连接的，应采用热压硫化胶合（橡胶止水带）或焊接（塑料止水带），其接头外观应平整光洁，抗拉强度不低于母材的80%。 不加任何处理的所谓“搭接”。橡胶止水带的各种交叉连结点，要使用我们成林公司生产成配件，以保证在施工中现场连接只在直线段进行。足够的变形能力，与混凝土具有良好粘接性能的柔性材料。

外贴式橡胶止水带EB型
It should be connected to the whole as far as possible in the factory. If the manufacturing process and transportation conditions are limited, hot pressing vulcanizing (rubber water stop) or welding (plastic water stop) shall be applied to the field connection. The appearance of its joints should be smooth and smooth, and the tensile strength is no less than 80% of the base bl. The so-called "lap joint" without any treatment. The rubber sealing belt of various cross junction, to use our company into the forest production parts, to ensure the construction site in the connection only in a straight line segment. Sufficient debation capacity, flexible material with good adhesion to concrete.
在橡胶止水带施工过程中，由于混凝土中有许多尖角的石子和锐刃的钢筋，所以在浇捣和定位止水带时，应注意浇捣的冲击力，以免由于力量过大而刺破橡胶止水带。如发现有破裂现象应及时修补，否则在接缝变形和受水压时，橡胶止水带所能抵抗外力的能力就会大幅度降低。 在定位橡胶止水带时，一定要使其在界面部位保持平展，更不能让止水带翻滚、扭结如发现有扭转不展现象应及时进行调正。在浇铸固定止水带时，应防止水带偏移，以免单侧缩短，影响止水效果。在混凝土浇捣时还必须充分震荡，以免止水带和混凝土结合不良而影响止水效果。止水带接头必须粘接良好，如施工现场条件具备，可采用热硫化连接的方法 。

外贴式橡胶止水带EB型
In the construction process of rubber sealing belt, because there are many sharp stones and sharp edged steel bars in concrete, when pouring and locating the sealing belt, we should pay attention to the impact force of pouring and tamping, so as not to pierce the rubber water stop because of too much power. If it is found that the rupture phenomenon should be repaired in time, otherwise the ability of rubber sealing belt to resist external force will be greatly reduced when the joint debation and water pressure are subjected to water pressure. When bing the rubber water stop, it must be kept flat at the interface, and even let the water stop roll and twist. If it is found that there is a twist and it does not appear, it should be adjusted in time. When casting fixed water stop belt, water belt shift should be prevented so as to avoid single side shortening and influence the effect of water stop. When the concrete is poured, it must also be fully concussion, so as to avoid the bad combination of water and concrete, which will affect the effect of water stop. The joint of the water stop belt must be well bonded, such as the condition of the construction site, and the b of hot vulcanization can be used.

河北瑞博橡塑制品有限公司是一家集橡胶支座，橡胶止水带，伸缩缝等工程橡胶制品为主的专业生产企业。欢迎各界朋友莅临参观指导，业务洽谈。欢迎致电：13166570832